Replace Nissan Key Fob Batteries
If your Nissan keyfob isn't responding to your commands, then its battery could be dead. Fortunately, this is a relatively easy repair that most people are able to do themselves.
You can get the replacement from a local hardware store or the owner's manual for the particular model you own and then follow these steps to change the battery.
Change the Battery
The key fob of your Nissan model is equipped with a built-in battery that will eventually lose its charge. The battery in the key fob can be changed in just a few minutes. You'll first need to purchase a CR2032 battery. It's a tiny coin-cell battery that is found in most key fobs. It is available in most convenience stores. You'll also require gloves (latex or non-latex) and small screwdrivers with flat heads to open the fob. Check The Key Lab for detailed instructions and steps before you begin.
Flip the fob upside down and look at the backside. You will see a small latch that you have to let go by pulling it down. This will release the mechanical key from the original position within the fob.
Then, you can insert the new battery and make sure that it is in the correct orientation. Close the fob after the battery is installed and then click the two sides of the fob together. After completing this final step make sure to test your key fob by pressing the unlock button and watching what happens. You'll now be able to utilize the numerous features of your Nissan If everything is working correctly. It's recommended to re-program the key fob following the change of the battery to make sure it's working properly.
Replacing the Transmitter
With your key fob serving as the "key" to many of your car's essential functions, it could be a serious blow if you misplace or damage it. If your key fob is damaged or dead, damaged key fob, you'll be left without the ability to lock and start your car.
So, it's a good idea to have an extra key fob in your possession in case of an emergency. Luckily, the procedure for replacing your Nissan key fob is simple. The process of replacing the Nissan key fob is quite easy. You'll need an entirely new flathead screwdriver and a new battery to remove the old.
You'll also need a Panasonic CR2032 3V round battery (you can find them in multipacks for less than $5 USD). The battery is located inside the key fob's back half and you'll need to gently turn the two halves to expose it. Make use of a flathead screwdriver or a small flathead to take off the clip that is on the top of the battery. Make sure to note its place of placement. Replace the battery and put the key fob back together, testing it to ensure it works properly.
As with any electronic device such as like all electronic devices, your Nissan Intelligent Key will eventually wear out due to regular usage and require to be replaced. To prevent this you should try to protect your key fob from water, magnetic fields as well as physical impacts Be careful not to drop it or place too much pressure on it.
Replace the Key
If your Nissan key fob has gone out and you're unable to use it to unlock or start your vehicle. This is a problem for those who have to travel to work in Detroit or to run errands near Dearborn, or enjoy some night out near Troy.
It's not that difficult to change the battery in your Nissan Smart Key. You can do it at home or at the dealership, and you'll usually get a battery for $5 or less at a hardware store.
Flip the fob upside down and push the small catch at the back. This will trigger the mechanical emergency key. The emergency key won't allow you to start your car but it will unlock the door.
Then, look for a small gap on the top of the casing for the key fob. These are perfect to insert an screwdriver through the slit, which allows you to take the two parts of the key fob apart. Once you've got access to the battery within, pull it out and note of its position. When you are ready to put back together your key fob, slide in the new battery and then snap the two components of the case back together. Insert the mechanical key and your Nissan smartkey will function like a normal key.
Other Issues
Many modern cars are equipped with key fobs that let the user to lock and start them without using keys for your car. The key fob is equipped with a transmitter to communicate with the computer system in the car.
There are a variety of reasons that your Nissan key fob does not work after you replace the battery. For one, the new battery may not be seated correctly inside the key fob. Resetting the key fob is another possibility. Fortunately, this is an easy procedure which can be carried out at home with just a few tools.
You'll require, for instance, a screwdriver with an angled tip to remove the battery that was in the key fob. With an screwdriver, you can pry the back of the keyfob open and then insert the new batteries. You'll also need to reprogramme your key fob for it to work with your vehicle.
You can easily program your Nissan key fob by yourself, since they can all be programmed by a user. It is usually done by inserting the key fob into the ignition twice within five minutes. If this doesn't work, you can bring your key fob to a dealer or an auto locksmith to have it programmed. The cost of this will depend on the person you speak with and what kind of car you own.